by Tom Gaylord, a.k.a. B.B. Pelletier
Today, we’ll finish the conversion of a Gamo 220 from steel spring to gas spring, and blog reader Vince gives us a report on the outcome.
If you’d like to write a guest post for this blog, please email us.
Take it away, Vince!
When we last saw the Gamo 220, I’d disassembled the powerplant and compared the old parts to the parts I ordered from Crosman. Today, I’ll install those new parts and test the gun for you.
The gun is laying on the bench, ready for assembly. The new piston slides in, followed by the gas spring. Be careful when sliding the piston seal past the end of the cocking slot and tuck the soft seal material away from the sharp edges of the cocking slot so the seal isn’t damaged. A flat-bladed screwdriver works well for this.
The new piston that works with the gas spring is slid into the spring tube. Notice that I’ve lubricated both ends of the new piston with moly grease.
The new gas spring (Nitro Piston) slides in after the piston. The small end of the spring fits into the socket inside the new piston I mentioned in Part 1. No lubrication is required.
The trigger and cocking link go back in (reverse order of removal), and the plain plate gets dropped into the rear spring retainer.
I’m dropping the plain plate into the rear spring retainer.
Now, I’m starting to sweat a bit. You see, I KNOW that the gas spring has a TON of pressure on it even when fully extended (very much unlike a coil spring) — so, how on earth am I gonna compress it enough to reassemble the gun? Oh, well, I’ll cross that bridge when I come to it –which is, well, right about now. After I install the rear retainer, I notice something.
There’s almost no preload on the gas spring
Almost no preload at all! THAT’S right. Because the gas spring is ALWAYS at or near full pressure, there’s plenty of preload pressure as soon as the piston comes off its stop, so very little preload travel is required.
What is preload?
When a conventional coiled steel mainspring is installed in a spring gun, it’s usually longer than the space into which it must fit. It is, therefore, necessary to compress the spring by some amount to get it to fit inside the spring tube. This compression causes the spring to be under pressure even when at rest — this is called preload. If you’ve ever seen a long, empty flatbed trailer on the interstate that looked bowed up in the center because there’s no weight on it, you’ve seen what no preload looks like. It takes several tons of weight just to get that trailer flat again — and much more to make it bow the other way.
Airgun tuners can add spacers that preload the mainspring even more when it’s resting, which causes it to develop greater power when compressed because it’s closer to its maximum potential that exists at the point when all the coils are touching. But gas springs don’t work that way. They’re under full compression (internal gas pressure) when they’re at rest. All cocking the gun does is move the internal piston against the already-compressed gas that’s ready to blast it back when the sear releases it. There’s a very small amount of additional compression of the gas, but it isn’t what makes the gas spring work as well as it does. The gas spring unit is always at full potential — even at rest.
So, this gas spring unit has very little farther to go at this point…under a quarter-inch, in fact. THIS sure makes things easy for me. Pry the retainer forward on one side while starting the pin through the other. [Note: If I used a mainspring compressor, I wouldn't need to pry anything. I would just tighten the compressor until the assembly pin holes lined up, then insert the large crosspin.]
The crosspin will go in, but the hole for the rear spring retainer bolt (that large-headed bolt I removed when I disassembled the powerplant in Part 1) doesn’t line up with the hole in the spring tube. This is a problem.
Immediately, a problem becomes apparent. Look at the hole where the rear spring retainer bolt goes. It’s not lined up with the hole in the tube. There’s approximately a .080″ misalignment here. This ain’t gonna work. My first inclination is to simply elongate the hole. But when I reinstall it, there’s another problem.
There’s a gap between the plate on the spring retaining bolt and the trigger assembly. It won’t support the trigger this way!
The trigger isn’t properly supported by the plate that’s attached to the bolt. Worse, this changes the spacing between the front and rear stock screws and doesn’t allow the action to be reinstalled.
Hmmm. I’m wondering if this is exactly what Crosman (or BAM) had in mind — preclude an easy conversion with existing parts (since the same problem would exist on a normal Quest). That leaves me thinking: Can I just butt the gas spring against the original Gamo spring retainer?
If you look at the picture of the new rear spring retainer above, you’ll see that there’s a small plate that drops into the cup that retains the gas spring cylinder. The cylinder wants to butt up against a flat surface, and the Gamo retainer has a large (approx. 1/2″) hole in it. I need a metal plate to go over it. Wait a minute! I’ve got one right here in my pocket!
A perfect spacer for the new gas spring and it costs — well, about a quarter!
And, so, it gets reassembled. Believe it or not, the whole thing works.
Time to test!
I’ll run through this pretty quickly — the velocity is now up to about 964 f.p.s., which represents a muzzle energy of about 14.5 ft-lbs. Not killer, but obviously a lot better than the detuned gun. Accuracy shouldn’t be changed — or should it? Oftentimes, guys will detune their guns to make them more accurate — or to simply make them easier to shoot. That might have some merit, as I now couldn’t break 0.37 inches at the same range. Not a big difference, and I’m certainly not gonna suggest that the gas spring decreased accuracy. But I don’t think it helped.
So what’s it like to shoot?
First of all, everything anyone ever said about “thunk” vs. “sproing” is absolutely correct. The gun “wumps” with a gas spring, and you can actually feel a kick back into your shoulder. Nothing like a typical centerfire gun, although maybe something like an 1894 shooting low-velocity .38 specials might be comparable. But that’s just a guess.
Cocking the gun is another matter. Effort peaks at about 33 lbs., which isn’t all that high — except for the fact the effort before that peak is certainly a lot higher than with a normal coil spring. This is what we’d expect, of course, with the relatively constant pressure of the gas spring. It isn’t unbearable, but it does take some getting used to.
Back to a coiled steel mainspring
After about 40-50 rounds, I decided it’s time to restore the gun back to original spec. I rummage around my spring box and find a REAL low-mileage Gamo spring, and put it all back together the way God intended it. NOW, I can really get a back-to-back series of impressions.
First, the velocity did drop a smidgen. It’s now down to an average of about 943 f.p.s., or a little under 14 ft-lbs. Second, and despite the tar on the spring and rear guide, we DEFINITELY are sproinging ourselves rather energetically. Lastly, the cocking effort is predictably much milder. Peak effort is down by 5 lbs., and the effort before that peak is even easier. Accuracy is unchanged from the gas spring.
How did my quarter, er, my impromptu gas spring backing plate pan out? Not too well.
The pressure of the gas spring punched a deep divot into the quarter.
The flip side doesn’t look any better.
I flattened it back out with a hammer, and I’m really hoping it’s still legal tender. Anyway, as I sort of expected, the relatively soft quarter didn’t do well. The backing plate really ought to be steel, 0.060 inches (1.5mm or 1/16″), just like the original.
But the bigger problem wasn’t the quarter.
There’s a serious indication of metal-to-metal galling.
There was some serious metal-to-metal contact going on here between the cylinder of the gas spring and the inside of the piston. If you look at the above pictures of the quarter, you’ll see that the indent isn’t centered. The pocket in the original rear spring retainer keeps the spring cylinder right in the middle, and apparently that’s real important because it won’t center itself.
And that’s about it for now. If this is going to work, we need a simple and cost-effective way of keeping the gas spring centered properly without permanently altering the original parts…and do it in a way that the average tinkerer can accomplish on his own. The first thing that comes to mind is to drill and tap a new hole in the new rear spring retainer, opposite of and slightly forward of the existing hole. I tried that, and found (predictably) that getting the hole in just the right spot is a bit difficult without a custom drilling jig.
For now, I’m just going to give it some thought.
WAIT! I JUST GOT AN IDEA….