Posts Tagged ‘H&N Baracuda Match pellets’
by Tom Gaylord, a.k.a. B.B. Pelletier
Today, we’ll test the Walther 1250 Dominator at 50 yards. I had to go out to the rifle range for this test, and we’ve been having some winds lately, so it took some time before I got a calm day. But this day was perfectly calm — I couldn’t have asked for a better day to shoot an air rifle at long range.
As you recall, the Dominator takes a 300-bar fill, which is 4,350 psi. I had to delay the test to get my carbon fiber tank refilled, and even then I didn’t have enough air for a full fill. When you fill a tank, it gets warm; and when it cools back down, you lose several hundred psi. I was able to fill to about 4,100 psi this time, but that single fill was enough air to last for the entire test, which was about 50 shots. And the needle in the pressure gauge is still in the green, which means there are more full-power shots remaining in the rifle.
I normally shoot from one of two mechanical rifle rests when I’m at this range, but for this test I decided to use my long sandbag, instead. The rifle lays in the crease on top of the bag and doesn’t move. There’s also more flexibility to reposition the rifle when required. Since this is a repeater that has to be reloaded, this flexibility was a good.
Since the circular clip holds 8 pellets, I decided to shoot 8-shot groups. It’s too much trouble to load just two pellets by themselves. So, all the groups seen today are 8-shots.
The first pellet was the venerable RWS Superdome. They landed close enough to the bull that I didn’t bother to adjust the scope. Eight pellets made a group that measures 2.017 inches between centers. The pellets spread out horizontally, but there was no wind whatsoever. I don’t think this pellet is suited to the rifle.
Following this, I adjusted the scope up and to the left just a little to compensate for where the Superdomes had landed. Then, I shot a group of JSB Exact Heavy pellets.
JSB Exact Heavy
I expected the JSB Exact Heavy dome pellet to give good groups, and it did — sort of. Seven of the 8 pellets landed in a group that measures 0.753 inches between centers. But 1 shot landed apart from the group, opening it up to 1.933 inches. This shot was somewhere in the middle of the string of 8. It wasn’t the first or last shot, and there was no called flier. It’s just somewhere in the string.
When something like this happens, I’m tempted to believe that it was caused by a defective pellet or by something just as obviously wrong. I think the JSB Exact Heavy is a good pellet for this rifle.
I probably shouldn’t have tried Beeman Devastators because they’re essentially wadcutters in profile, and wadcutters don’t do well at long distances. But I did try them, and they strung vertically into a group that measures 3.067 inches. Obviously, they’re a non-starter for this rifle at 50 yards.
JSB Exact RS
Next, I shot a group of JSB Exact RS domes. As light as they are, I wouldn’t normally recommend them for a precharged rifle of the Dominator’s power but had them along, so why not? Eight went into 0.945 inches, so I’m glad I tried them. This was the smallest group of the test. I do want to emphasize that the day was calm, because these light pellets do get blown around a lot.
Crosman Premier 10.5-grain
Next up were the heavy Crosman Premier 10.5-grain pellets. I expected them to do well in this rifle, and they didn’t disappoint. Eight went into a group measuring 1.19 inches between centers. While that number sounds a little large, look at the group it represents. It’s a little vertical, but it’s not a bad group.
Crosman Premier 7.9-grain
The last group I shot was with the 7.9-grain Crosman Premier lite. Eight of them made a group measuring 1.371 inches. That’s a little large when there are other pellets that are better, but it’s not a bad showing for 8 shots at 50 yards
The bottom line
I was glad to finally have the chance to test the Walther 1250 Dominator. It was a good rifle, overall, but I took exception to removing the air tank to fill it, the high fill pressure and the discharge noise.
However, out at the range, the rifle was much quieter — far quieter than a rimfire. Also, the trigger that I complained about when shooting indoors was actually no problem outside. I don’t know what the difference was, except that it was a different day and I saw things differently. I must say, there are a lot of very powerful shots in the tank once you get it up to pressure.
I did get used to fiddling with the bolt handle, and the rifle fed without a problem during this test. Installing the rotary clip is easier than on most other PCP rifles.
I would have to say that the 1250 Dominator is a fine precharged air rifle, but it runs into a lot of stiff competition. Buyers will get it because they like the overall styling, the all-weather materials it is made from and the high shot count.
by Tom Gaylord, a.k.a. B.B. Pelletier
Let’s look at the Walther 1250 Dominator accuracy at 25 yards. In deference to the 8-shot clip, I’m shooting 8-shot groups rather than 10. The way this rifle loads, with the clip almost disappearing in the receiver, it’s too difficult to keep track of those 2 extra shots.
I’ll be honest — I stalled testing this gun in the house because of the noise. It’s one of the loudest airguns I’ve ever shot indoors.
I said last time that I would give you a shot count once I filled the rifle to 4,350 psi (300 bar). Well, that didn’t happen. I filled it as far as my freshly filled carbon fiber tank would go, but that was only to 4,200 psi on the tank’s gauge, which seems pretty accurate. The rifle’s gauge showed a lower fill pressure, but I chalk that up to small pressure gauges never agreeing.
I didn’t get a complete shot count. I did, however, fire about 40 shots in the test and still had air remaining for at least another 15. If you can get the gun completely filled, there have to be at least 55 full-power shots available. Probably more, but at least 55.
I mounted an AirForce Airguns 4-16X50 scope on the rifle in a BKL 1-piece cantilever mount. The scope was low over the receiver, even though the BKL mount is a high one; but because the circular clip is entirely contained within the receiver, there was no interference.
I shot from a sandbag rest at 25 yards off an MTM Case-Gard Predator shooting table. In a moment that will become important to know.
I sighted the rifle in and started shooting with the H&N Baracuda Match pellet. It was accurate enough, but I felt the rifle could do better. Eight shots went into a group measuring 0.597 inches between centers.
The Baracuda Match pellets didn’t give me what I wanted, so I switched to 10.34-grain JSB Exact Heavy domes. They started out doing better than the Baracudas and produced a 0.522-inch 8-shot group. But two pellets strayed from the main group. I called the one that went to the left, but not the other one that went high. So, as good as this pellet is, it isn’t the best pellet in this rifle.
Then, I tried RWS Superdomes — a pellet that many of you favor over just about all others in .177 caliber. And this is where I had an epiphany with this rifle. The first 8-shot group measured 0.461 inches, but it was full of wild shots that went off when I wasn’t on target. That was both the fault of the trigger and the rifle’s light weight. I’ll address it in a moment. But this target told me that this rifle could shoot much better if I really tried.
The Walther 1250 Dominator is a very light rifle, and the trigger isn’t that light. As a result, the gun moves more than a little as the trigger is squeezed. This can be overcome by paying extreme attention to detail on each shot, but it’s something I normally don’t need to do when shooting an accurate PCP.
That’s why I mentioned the shooting table and sandbag rest. Normally, such things are an absolute lock for the guns, but this time the rifle is so light that it still moves around too much. You’re only going to solve that with technique.
The next group was shot with as much concentration as if I were using the artillery hold. And the payoff is a 0.404-inch 8-shot group. That represents the best I can do with this rifle and pellet at 25 yards.
The bolt is hard to cock and sticks when pushing it forward to load the pellet. It isn’t much of a hinderance, but you do notice it. I did discover that if the bolt is worked fast and with authority, it does become smooth. So, the rifle likes to be treated like an SMLE.
Opinions thus far
I found things to criticize on the Walther Dominator 1250. No. 1 is the need to fill it to 300 bar. That’s just too much pressure, and it uses all the air I can get. The rifle is very loud, and I’m no longer used to pneumatic air rifles being so loud. The trigger is too heavy and long, and the rifle needs to weigh at least 2.50-3.00 more lbs. to be stable. However, all that pales when we look at the accuracy.
This is an accurate air rifle — make no mistake. Today’s test was at 25 yards, so it’ll be very interesting to see what happens when we move to 50 yards.
by Tom Gaylord, a.k.a. B.B. Pelletier
Today, you’ll see the test of the .177-caliber Walther LGV Master Ultra at 25 yards with open sights. This is for all who have an interest in a rifle that I think redefines the breakbarrel spring-piston sporter.
Twenty-five yards is not quite 2.5 times the distance at which the first test was conducted, so I expect to see the groups open up quite a lot. In fact, this is a wonderful distance at which to test an airgun because this is where the real pedigree starts to show through. Let’s see how our test rifle did.
Crosman Premier lite
The first pellet I tested was the 7.9-grain Crosman Premier lite that did so well in the 10-meter test. After confirming the shot was on the bull with a spotting scope, I shot the remaining 9 shots without looking again. Shot 9 was a called pull to the left, and I knew I would see a hole to the left of the main group when I examined the target.
Crosman Premier heavies
Next, I tried 10 Crosman Premier heavies because a reader thought they might do well. They did not — giving a very open and scattered group that measures 1.549 inches between centers.
Next, I shot 10 Beeman Devastator pellets. These lightweight hollowpoints surprised me in the Pellet velocity versus accuracy test I did two years ago. And they fit the LGV breech very well, so I had hopes they might be accurate, as well.
Indeed they were! Ten gave a 1.154-inch group, but 9 of them were in 0.746 inches. That’s very much like the Premier lites, though there was no called shot this time.
JSB Exact Heavy 10.34-grain
Next up were 10 JSB Exact heavys. The Exact RS pellets had not done well in the 10-meter test, but these heavier domes often succeed where the lighter ones don’t. This time, the outcome was very telling. Eight of the pellets made an incredibly small 0.518-inch group that’s perfectly round, then the final two shots enlarged the group to 2.147 inches. They made both the largest and smallest group of the session! That small inner group tells me that this may well be the most accurate pellet in this rifle, as it often is.
This group made by JSB Exact Heavy pellets will make you think! I didn’t call any shots, but I think something went wrong with the two outliers. I believe the small cluster is more representative of what this pellet can do in this rifle.
Of course, I could be wrong, but this isn’t the last time I’m going to shoot this LGV for accuracy. Next time will be at 25 yards with a scope mounted. This JSB just won a place in that test.
H&N Baracuda Match
The last pellet I tested was the H&N Baracuda Match, which did so-so in the 10-meter test. I thought I would give them another chance at 25 yards; but, alas, their mediocrity only continued. Ten made an open 2.121-inch group with no pattern or clustering.
Am I satisfied?
I am very satisfied with this performance. The naysayers will probably dream up new things to say about the gun; but as far as I’m concerned, it’s on track for a spectacular test.
I will say that the firing behavior was quite buzzy with the Premiers, but much less so with the Baracudas and the heavy JSBs. I think those JSBs are going to turn out to be the pellets of choice in this rifle. I’ll also comment that the trigger now seems as good as a well-adjusted Rekord. It’s not as light, but the wide blade makes the release feel very crisp.
by Tom Gaylord, a.k.a. B.B. Pelletier
This comment came in last week from our new blog reader Jim H, and I wanted to address it right away. It’s a good question for a new airgunner to ask, and it deserves a good answer.
“I’m new to the airgun side of things, so I have a lot of questions but here’s one that is really bugging me. I have read all of the reviews here by Tom and also the blogs over at that “other airgun retailer” written by Jack Elliot. One message that has come through loud and clear is that each gun will tend to like specific pellets and only experience will tell the shooter which one is best. What is the best approach for testing various pellets? Do you pick a velocity that you want to shoot at and then try all the pellets that will get you to that velocity range or do you simply have favorite pellet brands and types that you’ve come to love over the years and that’s what you go with? With the hundreds of pellets available out there, what is the ’short list’ of pellets that a newbie needs to start with?”
Several of you started to answer Jim in the comments section, so my answer comes a little late; but from what I’ve read, I’m telling him things that are pretty different from what all of you told him. He actually asked 2 different questions: 1. What is the best way to test a pellet? and 2. What is a short list of pellets to choose to test airguns? I took my direction for this report from his request for a “short list” for a newbie.
This will not be a very technical report. I’m not going to discuss pellet head sizes or skirt thicknesses, except where it affects the pellets I name. I have a short list for most of the airguns I shoot, and it’s not rigid. But it’s caliber-specific, and there’s also a small powerplant component to it.
Money is no object
I used to focus on the cost of pellets, but that was before discovering that hitting the target is far more important than saving money. If saving money is your principal goal, get a piggybank. I shoot for fun, and hitting the target is where the fun is. It costs no more to be accurate than it does to experiment by chasing the illusion of economy.
I must also say that I have more experience with pellets for rifles than for pistols. So, today we’re just looking at pellets for rifles. Let’s take a look at them.
For .177 rifles my short list is the following pellets:
Crosman Premier lites (brown box) springers and CO2
Crosman Premier heavies (brown box) pneumatics and CO2
JSB Exact RS (up to 12 foot-pounds)
JSB Exact Heavy 10.3-grains
H&N Baracuda and Baracuda Match
Beeman Kodiak and Kodiak Match
That is my short list. There are other pellets that are very accurate, but I find them to be more specific to certain guns. Please remember that this is not a popularity contest. If your favorite pellet didn’t make my list, don’t fret. I try other pellets all the time — these are just the ones I count on.
If you ask me why these pellets are on the list, it’s because they’re the ones that are the most reliably accurate. That’s my only criteria because if you can’t hit the target, nothing else matters.
The .20-caliber list is very short because there aren’t as many reliable pellets made in that caliber. The most reliable one is the Crosman Premier.
Other than that, I would try anything JSB makes, and that’s about it.
The quarter-inch caliber is another one with few good pellets. The two on my list have demonstrated they will deliver in all cases.
Benjamin domed (these have no name, but they are essentially a .25 caliber Premier)
JSB Exact King
I prefer domed pellets to all other shapes. They’re more accurate at long range and penetrate well. Wadcutters are good for distances under 25 yards but not for farther than that.
Pointed pellets, hollowpoints and lead balls
I have no use for pointed pellets of any kind. I’ve never found them to be accurate, and the slight advantage they have in penetration isn’t good if they can’t hit the target. Hollowpoints are a subject that need a blog report of their own. Lead balls are specialized for certain airguns and are not for most air rifles.
Pellets and power
As power goes up, the pellets should generally get heavier. And PCPs tend to do best with heavier pellets. CO2 guns are a lot like PCPs when it comes to pellets, so I consider them to be the same.
Other selection criteria
There are other selection criteria, of course. I’ve found certain pellets to sometimes be surprisingly accurate in certain guns, and that’s enough to keep me trying them in other guns — searching for more miracles. But the lists above are the tried-and-true performers that almost never let me down. That’s why they made my list.
The second question
The other question Jim asked was how to test pellets. I do it by choosing the most accurate rifle I have and shooting 10-shot groups with each pellet in which I’m interested. Do it that way, and pellet testing is easy.
I usually don’t express my opinions this strongly; but when it comes to picking a good pellet, I think it’s too important to let it slide.
by Tom Gaylord, a.k.a. B.B. Pelletier
Now that we know how powerful the new .177-caliber Walther LGV Master Ultra is, people are lining up to see it shoot. We get to that today. I’ll start at 10 meters because I’m using the good open sights that come on the rifle; but as I mentioned in the last report, there will be other accuracy tests yet to come. While I’m not keeping this rifle like I did the .22, I don’t mind having it around awhile. Also, I’m writing a feature article about these new rifles for Shotgun News, so I have to do the testing anyway. I love my job!
For today’s report, I shot the rifle rested at 10 meters. Although that is an easy test for what we assume will be an accurate rifle, it is sensible because the open sights are being used. If the rifle really is accurate, I may also shoot the rifle with open sights at 25 yards because I’ll have confidence that it can do it. I haven’t mentioned this yet, but I shot the other couch in our living room about a month ago (I shot the first couch a few years ago), and we have since bought two new couches that I’m absolutely not allowed to shoot. So, any rifle I test has to be accurate…guaranteed.
I’m going to write a report this week for Jim H. on how to pick a good pellet, but let’s get that started today with how I selected the pellets for this rifle. I picked three for this rifle based on the power I thought it might have, which the velocity testing had demonstrated varied widely from 13 to 16.25 foot-pounds. I chose the JSB Exact RS dome because it’s been a wonderful pellet in lower-powered airguns, though in this one it’s up pretty high. I chose the H&N Baracuda Match because it often proved accurate in .177 rifles of wide-ranging power. Some say this spring rifle is too underpowered for a pellet this heavy and that the mainspring will suffer from shooting it, but I strongly disagree. I’ve used them in many rifles of this same power, and they usually worked well. The last pellet I tried is the 7.9-grain Crosman Premier lite, which has always been an accurate pellet. Sometimes, it’s even the absolute best in rifles of this power.
That was my pellet selection criteria for this rifle. It’s not scientific — it’s based on experience and some other factors I’ll talk about. I could just as easily have chosen 3 or 4 other good pellets for this test, but that would have been about all for this rifle, in my experience. Be sure to read that pellet-selection report later this week.
The rifle was shot off a rest at 10 meters. The rest was a sandbag on which I rested my off hand, then I rested the rifle on the flat of my palm, with the heel of my hand touching the triggerguard.
H&N Baracuda Match
The first pellet up was the heavy H&N Baracuda Match. The first shot was made without adjusting the sights. The pellets landed low but centered, so I dialed the rear sight up about 5 clicks. The next shot landed in the black, so I settled in and fired 9 more pellets without looking through the spotting scope. After the 10 shots, I knew we had another winner and how this report was going to end. This rifle is great, just like the .22, only more powerful.
Now, we’re on a roll. I expected great things from it, and the Premiers were up next.
After making certain that the first pellet was on target, I shot the other 9 without looking. When I went down to change the target I came upon a near-screamer of a 10-shot group. Ten Premier lites went into 0.325 inches. Yes, I’ve shot smaller groups at 10 meters, but maybe not with open sporting sights — I don’t really remember. This is justification for including this pellet in the test.
JSB Exact RS
The last pellet I tested was the light JSB RS dome. Again, the first pellet landed in the bull, so I stopped checking. Nine more went downrange, then I walked down to pull the target. This time the group wasn’t very good, which was something of a surprise. The group measures 0.666 inches between centers. I’ll shoot this pellet again at 25 yards, but I’ll be careful when I do.
JSB Exact RS pellets didn’t do as well as I’d hoped. This group is twice the size of the Premier group; and because this is 10 shots and not 5, it’s not just an estimate of accuracy: It’s the final word.
The trigger on this rifle continues to excel. And the sights are exceptional. The firing cycle is smooth and relatively free of buzz. But I imagine that will vary, rifle by rifle. And as it breaks in, I think it’ll become increasingly smoother.
I like the shape of the stock. I said that about the synthetic-stocked Walther LGV Challenger in .22 caliber I tested before, but this stock has a more conventional shape. The balance is slightly muzzle-heavy, which I find ideal.
Next, I’ll back up to 25 yards and test it there with open sights. But you already know how this is going to turn out. The new Walther LGV family of sporting spring rifles is a very refreshing change to the usually similar new airgun models.